Pico Technology Oscilloscope Probe, Probe Type: Active, Differential 50MHz 600V

產品概覽和技術數據資料表
法例與合規
相容
COO (Country of Origin): TW
產品詳細資訊

Pico 50MHz 70V Differential Probe TA058,10:1

Pico TA058 is a 50MHz bandwidth active differential probe suitable for high common-mode voltage measurement applications up to ±700V (DC + peak AC). This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high-voltage differential measurements. Applications include making safe measurements in power circuit applications and acquisition of low-speed balanced differential signals found in serial communications buses. The TA058 is suitable for measuring transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays, as well as signals in the millivolt range from sensors and other instrumentation. The differential inputs make it possible to measure voltages on floating circuits.

Bandwidth DC to 50MHz (–3 dB)
Attenuation ratio 10:1
Accuracy ±1%
Rise time <7ns
Input impedance 1.6MΩ ll 7pF each side to ground
Differential range ±70V (DC + peak AC) or 70VRMS
Common mode range ±700V (DC + peak AC) or 600VRMS
Absolute maximum voltage (either input to ground) ±700V (DC + peak AC) or 600VRMS CATI
Swing ±7V into 5kΩ load
Offset (typical) <±2mV
Noise (typical) 0.7mVRMS
Source impedance (typical) 50Ω
CMRR (typical) 95dB @ 60Hz; 60dB @ 1MHz
Ambient operating temperature -10 to +40 °C
Ambient storage temperature -30 to +70°C
Power requirement 4xAA cells or 6VDC/90mA mains adaptor or regulated 9VDC/70mA mains adaptor
Length of input leads 50cm
Length of BNC lead 125cm
Weight 300g
Dimensions 111 x 22 x 14 mm

Pico Technology Oscilloscope Probe

The Pico Technology TA058 oscilloscope probe is an active differential probe, suitable for high common-mode voltage measurement applications up to ±700V. It can be used with a signal speed of up to 50MHz. This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high voltage differential measurements.

Features and Benefits

• Bandwidth is DC to 50MHz (–3dB)
• Attenuation ratio is 10:1
• Accuracy is ±1%
• Input impedance is 1.6Mohm ll7pF each side to ground
• Differential range is ±70V (DC + peak AC) or 70VRMS
• Maximum differential is ±700 V (DC + peak AC) or 600VRMS
• Common mode range is ±700V (DC + peak AC) or 600VRMS
• Absolute maximum voltage is ±700V (DC + peak AC) or 600VRMS CAT I
• Swing is ±7V into 5Kohm load
• Offset (typical) is <±2mV
• Noise (typical) is 0.7mVRMS
• Source impedance is 50ohm
• CMRR (typical) is 95dB at 60Hz and 60dB at 1MHz
• Ambient operating temperature ranges between -10°C and 40°C
• Power requirement 4xAA cells or 6VDC/60mA mains adaptor or regulated 9VDC/40mA mains adaptor

Applications

• Safe measurement in power circuit
• Acquisition of low speed balanced differential signals found in serial communications buses
• Transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays
• Signals in the milliV range from sensors and other instrumentation

Certifications

• IEC-1010.1
• IEC-1010.2-031 CAT III
• Pollution Degree 2

規格
Attribute Value
Probe Type Active, Differential
Attenuation 1:10
Bandwidth 50MHz
Maximum Common Mode Input Voltage 600V
Number of Probes 2
Safety Category Level CAT I
Safety Category Voltage ±700 V, 600 Vrms
Safety Category CAT I ±700 V, 600 Vrms
8 現貨庫存,可於3工作日發貨。
單價 個
HK$ 3,835.03
(不含稅)
單位
Per unit
1 +
HK$3,835.03