Fluke 773 Clamp Meter, 100mA dc

  • RS庫存編號 669-3493
  • 製造零件編號 Fluke 773
  • 製造商 Fluke
產品概覽和技術數據資料表
法例與合規
不適用
COO (Country of Origin): CN
產品詳細資訊

772 & 773 Milliamp Process Clamp Meters

Need more hours in your day? Save time by not breaking the loop on 4-20 mA signal measurements with the Fluke 771 Process Clamp Meter.

Are you spending time:

•Taking mA measurements by removing a wire and breaking the loop •Calling the control room to isolate a loop
•Testing analog input/output on a console
•Troubleshooting devices with mA inputs and outputs
•Repairing intermittent or erratic 4-20 mA loops
•Going back to the shop to get extra tools

If you need more time in your busy day take a good look at the Fluke 772 and 773 mA Clamp Meters. Designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system.

Here are some specific ways the Fluke 772 and 773 clamp meters will help you:

Measure mA signals for PLC and control system analog I/O without breaking the loop
•Measures low level dc current
•Correlate process indication with real physical value

Measure output signals from transmitters without breaking the loop
•Maintain and troubleshoot process and automation equipment without breaking the loop
•No disruption to the process

Detachable clamp with extension cable
•Measurements in tight locations
•Enables measurements in difficult situations

Measurement Spotlight
•Illuminates hard to see wires in dark enclosures
•Measurement process is easier and quicker

Measure up to 99.9 mA range non-contact
•Wide range of measurements
•Measures 10 to 50 mA signals in older control systems

Automatic power off
•After 15 minutes and 2 minute automatic off for backlight and spotlight
•Saves battery life

Want simultaneous mA source/measure? Consider the Fluke 773 Milliamp Clamp Meter.

Features and Benefits

•Best in class 0.2% accuracy
•0.01 mA resolution and sensitivity
•Measure 4 to 20 mA signals without “breaking the loop”
•Measure mA signals for PLC and control system analog I/O
•Dual backlit display with both mA measurement and percent of 4 to 20 mA span
•Measurement Spotlight illuminates hard to see wires in dark enclosures
•Detachable clamp with extension cable for measurements in tight locations
•Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
•Automatically change the 4 to 20 mA output for remote testing
•Power saving features, auto-off, backlight timeout extend battery life
•Hold function captures and displays changing measurements
•Measure 4 to 20 mA signals with in-circuit measurement
•Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
•Source 4 to 20 mA signals for testing control system I/O or I/Ps
•mA output linear ramp or 25% step output
•Automatically change the 4 to 20 mA output for remote testing

Fluke 772 additional features:

Source 4 to 20 mA signals for testing control system I/O or I/Ps Simulate 4 to 20 mA signals for testing control system I/O
Measure 4 to 20 mA signals with in-circuit measurement
Simultaneously measure mA in-circuit with 24 V loop power for powering and testing transmitters
Source mA output signals in a linear ramp or 25 % step output for remote testing
Power saving features, auto-off, backlight timeout extend battery life

Fluke 773 additional features:

DC voltage measurement to verify 24 V power supplies or voltage I/O signals
Source dc voltage to test input devices that accept a 1 to 5 volt or 0 to 10 volt signal
Scaled mA output corresponds to the 4 to 20 mA signal measured by the mA clamp enables a logging DMM or other device to record the 4 to 20 mA signal without breaking the loop mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal
Voltage output linear ramp or 25 % step output
Automatically change the voltage output for remote testing

Note

For details of the 771 process clamp meter see stock no. 287-642

Supplied with

4 AA alkaline batteries, test lead set with integral prods and 2 crocodile clips; test leads with integral grabber clips; soft carry case & instructions

Fluke Clamp Meter

The Fluke milliamp process clamp meter measures current up to 99.9mA DC and voltage up to 30V DC. It saves time and money by measuring 4mA to 20mA signals five times faster than with traditional DMMs, and without breaking the loop. It can detach the clamp section of the meter and use it as a remote jaw, connected to the main body by an extension cable to make it easier to take measurements in tight spaces. Note:For details of the 771 process clamp meter see stock no. 287-642Supplied with:4 AA alkaline batteries, test lead set with integral prods and 2 crocodile clips test leads with integral grabber clips
soft carry case & instructions

Features and Benefits

Sources 4mA to 20mA signals for testing control system I/O or I/Ps Measures 4mA to 20mA signals with in-circuit measurement Simultaneously measures mA in-circuit with 24V loop power for powering and testing transmitters Source output signals in a linear ramp or 25% step output- Automatically change the 4mA to 20 mA output for remote testing Power-saving features, auto-off, backlight timeout extend battery life DC voltage measurement to verify 24V power supplies or voltage I/O signals Source DC voltage to test input devices that accept a 1V to 5V or 0V to 10V signal The scaled output provides a continuous mA signal that corresponds to the 4mA to 20mA signal measured by the mA clamp- Output mA signal enables a logging DMM or other device to record the 4mA to 20mA signal without breaking the loop mA in/out: simultaneously measure the mA signal with the clamp and source an mA signal - apply an mA input signal to a device and measure its 4mA to 20mA output on devices such as valves or mA isolators Voltage output linear ramp or 25% step output- Automatically change the voltage output for remote testing Delivers 0.01mA resolution and sensitivity Measurement Spotlight to illuminate hard to see wires in dark enclosure Operating temperature ranges between -10°C and 50°C

Applications

Troubleshooting transmitters Troubleshooting valves Troubleshooting programmable logic controllers (PLCs) found in process plants

Certifications

EN61010-1 IP40 rated

規格
Attribute Value
Absolute Maximum AC Current Measurement -, - A ac
Absolute Maximum DC Current Measurement 99.9mA dc
Absolute Maximum DC Voltage Measurement 30V dc
Model Number 773
DC Current Measurement Resolution 10uA
Best DC Current Accuracy ±1% + 5 Digits
Clamp Meter Type Milliamp Process Clamp
Best DC Voltage Accuracy 0.2% + 2 Digits
Height 41mm
Minimum Operating Temperature -10°C
Length 248mm
Width 76mm
DC Voltage Measurement Resolution 10mV
Dimensions 248 x 76 x 41mm
Power Source Battery
Functions Measured AC Current, DC Voltage
Display Type LCD
Battery Type AA
Maximum Operating Temperature +50°C
Weight 420g
Battery Life 12 h
Maximum Conductor Size 4.5mm
Jaw Capacity Busbars 4.5mm
當前暫無庫存,可於2020/5/6發貨。
單價 個
HK$ 12,272.62
(不含稅)
單位
Per unit
1 +
HK$12,272.62