- RS庫存編號:
- 729-2925
- 製造零件編號:
- E-1048-8I4-C3D4V1-4U3-20A
- 製造商:
- ETA
此產品已停售
- RS庫存編號:
- 729-2925
- 製造零件編號:
- E-1048-8I4-C3D4V1-4U3-20A
- 製造商:
- ETA
產品概覽和技術數據資料表
法例與合規
- COO (Country of Origin):
- DE
產品詳細資訊
Smart Power Relay E-1048-8I Series
The Smart Power Relay E-1048-8I is a remotely controllable electronic load disconnecting relay with three functions in a single unit:
- electronic relay
- electronic overcurrent prodection
- status indication
The 7-pin INLINE version is designed for use with various E-T-A terminal blocks, e. g. 17-P10-Si
Integral power electronics provide a wear-resistant switching function, insensitive to shock and vibration
Only a fraction of the control power needed by electro-mechanical relays is required for switching loads. This is important for battery buffered load circuits which have to remain controlled even with the generator off line
The extremely low induced current consumption of less than 1mA is absolutely necessary for battery buffered applications
The load circuit is disconnected in the event of an overload or short circuit, the trip curve is also suitable for smaller motor loads
The load circuit is permanently monitored for wire breakage
Two status outputs for control signal AS and group signal SF provide status indication
For processing the actual value of the current flow in a power management system an analogue output from 0 to 5 Volts is provided
Typical applications with DC 12V or DC 24V circuits, where magnetic valves, motors or lamp loads have to be
switched, protected or monitored
- electronic relay
- electronic overcurrent prodection
- status indication
The 7-pin INLINE version is designed for use with various E-T-A terminal blocks, e. g. 17-P10-Si
Integral power electronics provide a wear-resistant switching function, insensitive to shock and vibration
Only a fraction of the control power needed by electro-mechanical relays is required for switching loads. This is important for battery buffered load circuits which have to remain controlled even with the generator off line
The extremely low induced current consumption of less than 1mA is absolutely necessary for battery buffered applications
The load circuit is disconnected in the event of an overload or short circuit, the trip curve is also suitable for smaller motor loads
The load circuit is permanently monitored for wire breakage
Two status outputs for control signal AS and group signal SF provide status indication
For processing the actual value of the current flow in a power management system an analogue output from 0 to 5 Volts is provided
Typical applications with DC 12V or DC 24V circuits, where magnetic valves, motors or lamp loads have to be
switched, protected or monitored
Approvals
CE, e1 logo (according to EU, EMC and automotive directives).
For products that are Customized and under Non-cancellable & Non-returnable, Sales & Conditions apply.
Approvals
CE, e1 logo
規格
Attribute | Value |
---|---|
Maximum Load Current | 20 A |
Maximum Load Voltage | 32 V dc |
Minimum Load Voltage | 9 V dc |
Maximum Control Voltage | 5 V dc |
Minimum Control Voltage | 0 V dc |
Switching Type | DC |
Control Voltage Range | 0 → 5 V dc |
Terminal Type | Through Hole |
Output Device | MOSFET |
Relay Type | Power Relay |
Load Voltage Range | 9 → 32V dc |
Maximum Turn On Time | 5ms |
Dimensions | 50 x 11.5 x 56mm |
Operating Temperature Range | -40 → +85°C |
Special Features | LED Status Indicator |
Off State Leakage Current | 500 μA |
Maximum Operating Temperature | +85°C |
Minimum Operating Temperature | -40°C |
Depth | 11.5mm |
Height | 56mm |
Standards Met | CE |
Length | 50mm |